Here is a little video on how to solder Deans connectors then finishing off with the provided heat shrink tubing to cover everything up.
John
https://www.youtube.com/watch?v=AdmlB1e ... =autoshare
Search found 40 matches
- Thu 14 Nov 14 2013 9:20 am
- Forum: Support
- Topic: How to prepare your DragonLabs 80AMP Current Sensor
- Replies: 0
- Views: 27639
- Tue 31 Jul 31 2012 3:07 pm
- Forum: Support
- Topic: DragonOSD+ firmware upgrading
- Replies: 140
- Views: 299874
Re: DragonOSD+ firmware upgrading
Version 17.8
Accepts new LS20031 GPS with MT3399 chipset
Accepts new LS20031 GPS with MT3399 chipset
- Tue 24 Apr 24 2012 12:25 pm
- Forum: Support
- Topic: DragonOSD+ firmware upgrading
- Replies: 140
- Views: 299874
Re: DragonOSD+ firmware upgrading
Version 17.3 (for V2 hardware)
1. SW assigned switch will now clear AHI (won't leave lines on screen)
2. minor optimizations (very insignificant)
1. SW assigned switch will now clear AHI (won't leave lines on screen)
2. minor optimizations (very insignificant)
- Mon 06 Feb 06 2012 6:18 am
- Forum: Support
- Topic: DragonOSD+ board connections
- Replies: 14
- Views: 71964
Re: DragonOSD+ board connections
Installing the supplied current sensor in the PWM pins may result in damaging the OSD PPM.
- Mon 06 Feb 06 2012 6:14 am
- Forum: Support
- Topic: DragonOSD+ board connections
- Replies: 14
- Views: 71964
Re: DragonOSD+ board connections
Connecting the supplied current sensor incorrectly may result in permanently damaging the MCU! DO NOT DO THIS! Make sure the black wire is facing the EDGE of the OSD!
- Thu 12 Jan 12 2012 2:40 pm
- Forum: Support
- Topic: IMU Support for DragonOSD+ v2
- Replies: 9
- Views: 46302
- Thu 12 Jan 12 2012 2:39 pm
- Forum: Support
- Topic: IMU Support for DragonOSD+ v2
- Replies: 9
- Views: 46302
Re: IMU Support for DragonOSD+ v2
Once the firmware is loaded into your IMU and you did not receive an error message in Arduino, unplug the wires and connect the IMU to the Translator board and OSD. Power up the OSD, enter into menu mode and activate your artificial horizon by selecting values from 1 and up. Factory setting is (0) w...
- Thu 12 Jan 12 2012 2:34 pm
- Forum: Support
- Topic: IMU Support for DragonOSD+ v2
- Replies: 9
- Views: 46302
Re: IMU Support for DragonOSD+ v2
If you receive a avrdude message in the black box of Arduino, this may mean you have connected the IMU incorrectly!
- Thu 12 Jan 12 2012 2:32 pm
- Forum: Support
- Topic: IMU Support for DragonOSD+ v2
- Replies: 9
- Views: 46302
Re: IMU Support for DragonOSD+ v2
1) Press "upload"
2) When the message displays in the black box below, "Binary Sketch size..... ", quickly press the IMU "reset button."
Note: Razor IMU red and green LED will light up solid when the firmware has been loaded properly.
2) When the message displays in the black box below, "Binary Sketch size..... ", quickly press the IMU "reset button."
Note: Razor IMU red and green LED will light up solid when the firmware has been loaded properly.
- Thu 12 Jan 12 2012 2:29 pm
- Forum: Support
- Topic: IMU Support for DragonOSD+ v2
- Replies: 9
- Views: 46302
Re: IMU Support for DragonOSD+ v2
Double check your Board type and Serial Port under the "Tools" menu.