Search found 40 matches

by John Lee
Thu 14 Nov 14 2013 9:20 am
Forum: Support
Topic: How to prepare your DragonLabs 80AMP Current Sensor
Replies: 0
Views: 8965

How to prepare your DragonLabs 80AMP Current Sensor

Here is a little video on how to solder Deans connectors then finishing off with the provided heat shrink tubing to cover everything up.

John

https://www.youtube.com/watch?v=AdmlB1e ... =autoshare
by John Lee
Tue 31 Jul 31 2012 3:07 pm
Forum: Support
Topic: DragonOSD+ firmware upgrading
Replies: 140
Views: 68681

Re: DragonOSD+ firmware upgrading

Version 17.8

Accepts new LS20031 GPS with MT3399 chipset
by John Lee
Tue 24 Apr 24 2012 12:25 pm
Forum: Support
Topic: DragonOSD+ firmware upgrading
Replies: 140
Views: 68681

Re: DragonOSD+ firmware upgrading

Version 17.3 (for V2 hardware)

1. SW assigned switch will now clear AHI (won't leave lines on screen)
2. minor optimizations (very insignificant)
by John Lee
Mon 06 Feb 06 2012 6:18 am
Forum: Support
Topic: DragonOSD+ board connections
Replies: 14
Views: 26407

Re: DragonOSD+ board connections

Installing the supplied current sensor in the PWM pins may result in damaging the OSD PPM.
by John Lee
Mon 06 Feb 06 2012 6:14 am
Forum: Support
Topic: DragonOSD+ board connections
Replies: 14
Views: 26407

Re: DragonOSD+ board connections

Connecting the supplied current sensor incorrectly may result in permanently damaging the MCU! DO NOT DO THIS! Make sure the black wire is facing the EDGE of the OSD!
by John Lee
Thu 12 Jan 12 2012 2:40 pm
Forum: Support
Topic: IMU Support for DragonOSD+ v2
Replies: 9
Views: 10610

Re: IMU Support for DragonOSD+ v2

Video of this in action:
http://vimeo.com/35678431

Now you are ready to fly!!
by John Lee
Thu 12 Jan 12 2012 2:39 pm
Forum: Support
Topic: IMU Support for DragonOSD+ v2
Replies: 9
Views: 10610

Re: IMU Support for DragonOSD+ v2

Once the firmware is loaded into your IMU and you did not receive an error message in Arduino, unplug the wires and connect the IMU to the Translator board and OSD. Power up the OSD, enter into menu mode and activate your artificial horizon by selecting values from 1 and up. Factory setting is (0) w...
by John Lee
Thu 12 Jan 12 2012 2:34 pm
Forum: Support
Topic: IMU Support for DragonOSD+ v2
Replies: 9
Views: 10610

Re: IMU Support for DragonOSD+ v2

If you receive a avrdude message in the black box of Arduino, this may mean you have connected the IMU incorrectly!
by John Lee
Thu 12 Jan 12 2012 2:32 pm
Forum: Support
Topic: IMU Support for DragonOSD+ v2
Replies: 9
Views: 10610

Re: IMU Support for DragonOSD+ v2

1) Press "upload"
2) When the message displays in the black box below, "Binary Sketch size..... ", quickly press the IMU "reset button."

Note: Razor IMU red and green LED will light up solid when the firmware has been loaded properly.
by John Lee
Thu 12 Jan 12 2012 2:29 pm
Forum: Support
Topic: IMU Support for DragonOSD+ v2
Replies: 9
Views: 10610

Re: IMU Support for DragonOSD+ v2

Double check your Board type and Serial Port under the "Tools" menu.