Another setup with Arduino Mini pro 3.3v and FY-30A
Virgis
Search found 8 matches
- Mon 23 Jan 23 2012 9:51 pm
- Forum: Support
- Topic: DragonOSD+ FY-30 (AHI) connections
- Replies: 5
- Views: 38528
- Mon 12 Dec 12 2011 11:48 pm
- Forum: Support
- Topic: DragonOSD+ FY-30 (AHI) connections
- Replies: 5
- Views: 38528
Re: DragonOSD+ FY-30 (AHI) connections
Is either better ArduIMU or FY-30A? The main differences are: ArduIMU gives faster AHI draw (faster data flow, very faster :) ) ArduIMU doesn't need any extra devices to connect it. ArduIMU isn't available as v2, v3 is out, but is there a suitable firmware? ArduIMU DRIFTS VERY BADLY! FY-30: almost n...
- Sun 20 Nov 20 2011 4:55 pm
- Forum: Support
- Topic: DragonOSD+ firmware upgrading
- Replies: 140
- Views: 299864
Re: DragonOSD+ firmware upgrading
Daniel,
Then using Switch ch (for mAh/km and AHI ON/OFF), turning OFF AHI, it doesn't disappear from the screen. It just stays as it was the last draw. Thanks
Virgis
Then using Switch ch (for mAh/km and AHI ON/OFF), turning OFF AHI, it doesn't disappear from the screen. It just stays as it was the last draw. Thanks
Virgis
- Thu 10 Nov 10 2011 8:43 pm
- Forum: Support
- Topic: DragonOSD+ FY-30 (AHI) connections
- Replies: 5
- Views: 38528
Re: DragonOSD+ FY-30 (AHI) connections
Here the firmware for Arduino Mini Pro (only for 3.3v version, 8Mhz)
Firmware is the same as for ArduIMU, but has boudrate 38400 in place of 19200, because Arduino Mini works in 8Mhz frequency..
Virgis
Firmware is the same as for ArduIMU, but has boudrate 38400 in place of 19200, because Arduino Mini works in 8Mhz frequency..
Virgis
- Fri 04 Nov 04 2011 5:28 pm
- Forum: Support
- Topic: DragonOSD+ FY-30 (AHI) connections
- Replies: 5
- Views: 38528
Re: DragonOSD+ FY-30 (AHI) connections
Here is the connection using Arduino Mini Pro 3.3v (make sure you get 3.3v for this task, 5v isn't suitable). Firmware for Arduino Mini Pro will be posted latter. Since it is 8Mhz mcu. Needs higher boudrates (38400 in place of 19200 as it was ArduIMU). Pinout for Arduino Mini Pro: http://img27.image...
- Fri 04 Nov 04 2011 5:45 am
- Forum: Support
- Topic: DragonOSD+ FY-30 (AHI) connections
- Replies: 5
- Views: 38528
Re: DragonOSD+ FY-30 (AHI) connections
For 10Hz refresh rate from FY-30A, must flash new firmware into FY-30A. Instructions here: Download attached FY-30A firmware (in the bottom of this post). Read firmware update manual: http://shop.fyetech.com/dl/firmwarefy30a.pdf Firmware update program here: http://shop.fyetech.com/dl/fy30afirmware1...
- Fri 04 Nov 04 2011 5:09 am
- Forum: Support
- Topic: DragonOSD+ FY-30 (AHI) connections
- Replies: 5
- Views: 38528
DragonOSD+ FY-30 (AHI) connections
For those who has FY-30 as stabilizer and would like to use it as AHI (IMU) for DOSD+ 31207276 should follow this: You just need Arduino mini board (or similar with Atmega 328P and should be 3.3v level). Here I will use ArduIMU (as just converter). Step by step how to upload firmware (attached file ...
- Wed 12 Jan 12 2011 5:24 am
- Forum: Support
- Topic: DragonOSD+ DOSD Config Mission Editor
- Replies: 9
- Views: 129206
Re: DragonOSD+ DOSD Config Mission Editor
Chris,
For next version, can you add a question box for confirming mission removal (delete mission):
Thanks
Virgis
For next version, can you add a question box for confirming mission removal (delete mission):
Thanks
Virgis