DragonLink 12-channel receiver modification

Support related stuff, for various products
Post Reply
Daniel Wee
Site Admin
Posts: 2449
Joined: Wed 25 Feb 25 2009 8:00 pm

DragonLink 12-channel receiver modification

Post by Daniel Wee »

The DragonLink receiver is internally a 12-channel receiver but there wasn't enough space on the main board to accomodate all twelve headers so three channels were left out. To fully enable 12-channels, it is a matter of making the appropriate connections. Before attempting this, I should warn you that this involves some fine soldering and a fine tipped soldering iron, so unless you are very good with the iron, I would suggest not attempting it yourself. You perform this mod at your own risk.

To start with, you will need a small piece of perforated breadboard (Veroboard). Use a sharp blade and cut the trace on the board as follows:-
IMG_0754a.JPG
IMG_0754a.JPG (272.67 KiB) Viewed 35310 times
Then solder on the headers and wires as follows:-
IMG_0755a.JPG
IMG_0755a.JPG (274.96 KiB) Viewed 35310 times
IMG_0756a.JPG
IMG_0756a.JPG (319.38 KiB) Viewed 35308 times
The power wires should be thicker multi-stranded wires as they carry the power to the servos.
IMG_0763a.JPG
IMG_0763a.JPG (288.86 KiB) Viewed 35308 times
The signal wires are insulated magnet wires (thin red ones in the photos) and the insulation is removed at the other end in preparation for soldering to the MCU. You will need to remove the heatshrinking from the receiver board in order to have access to the MCU. When you do this, the spacing rubber between the boards may fall out. Be sure to keep it and replace it when you are done as it prevents the boards from bending and shorting.
IMG_0757a.JPG
IMG_0757a.JPG (162.57 KiB) Viewed 35307 times
These are soldered very carefully to the MCU. Be especially careful not to short out the wire to the ground via next to the CH10 pin.
IMG_0759a.JPG
IMG_0759a.JPG (349.77 KiB) Viewed 35307 times
IMG_0761a.JPG
IMG_0761a.JPG (259.19 KiB) Viewed 35307 times
Check that all the connections are secure and safe. You will need to replace the heatshrinking. If you separated the boards, you will need to connect them back correctly, making sure that the inter-board header is properly lined up. Ensure that the power wires (red and black ones) are not touching the SMA connector. You can solder those two wires anywhere along the bus, not just at the end.
IMG_0762a.JPG
IMG_0762a.JPG (255 KiB) Viewed 35309 times
You should also find a way of securing the extension board so that the wires do not fray over time. Those magnet wires need to be protected.

Good luck!
Daniel
John Lee
Posts: 105
Joined: Thu 26 Feb 26 2009 12:24 pm

Re: DragonLink 12-channel receiver modification

Post by John Lee »

This is what it should look like if you wish to remain the original board size.
Attachments
P1020686.JPG
P1020686.JPG (50.66 KiB) Viewed 35042 times
P1020688.JPG
P1020688.JPG (35.15 KiB) Viewed 35042 times
John Lee
Posts: 105
Joined: Thu 26 Feb 26 2009 12:24 pm

Re: DragonLink 12-channel receiver modification

Post by John Lee »

more photo's to come...
John Lee
Posts: 105
Joined: Thu 26 Feb 26 2009 12:24 pm

Re: DragonLink 12-channel receiver modification

Post by John Lee »

re-editing..
John Lee
Posts: 105
Joined: Thu 26 Feb 26 2009 12:24 pm

Re: DragonLink 12-channel receiver modification

Post by John Lee »

re-editing
JetPilot
Posts: 41
Joined: Wed 21 Oct 21 2009 10:20 pm

Re: DragonLink 12-channel receiver modification

Post by JetPilot »

Here is the 12 channel receiver I made for Andre, it is going into a helicopter, so it was important that this be compact, strong, and not prone to damage by constant vibrations. I glued down the magnet wires after it was done to make sure they would not fail under the constant vibrations of a helicopter nor be shorted or pulled by anything. As you see the finished receiver is is not any longer than the origional being that the SMA connector sticks out anyways. I am very happy with the way this receiver turned out, it should be just as strong, and damage resistant as the origional. The only bad part was the amount of extra time and work it takes to do this nicely, the next guy that wants this will pay an extra 50 bucks for this modification !!! But it should work out very well and trouble free for those few people that must have 12 channels.

Mike
Attachments
DSC03860.JPG
DSC03860.JPG (668.01 KiB) Viewed 34998 times
DSC03845.JPG
DSC03845.JPG (698.44 KiB) Viewed 34998 times
DSC03836.JPG
DSC03836.JPG (603.22 KiB) Viewed 34998 times
DSC03830.JPG
DSC03830.JPG (730.46 KiB) Viewed 34998 times
andrebandre
Posts: 1
Joined: Fri 07 Aug 07 2009 2:18 pm

Re: DragonLink 12-channel receiver modification

Post by andrebandre »

Thank you Mike Almighty.
I owe you a debt of gratitude for doing the delicate 12 ch brain surgery on the DL Rx.
Another thank you goes to Father Daniel and Brother John for making the DL a reality.
I suppose good things do come to those who wait.At least once in a blue moon.
Peace and clear blue skies,
Andre the undisputed long range heli FPV king of the hill
Post Reply